How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
In this article down the page you will find lots of dependable insights all about How to Install a Bathtub.
Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily available, the project can move easily; if you need to open a wall to get rid of the old bathtub as well as position the brand-new tub, the task is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and embeded in the brand-new one. Ensure you have qualified on your own for the task and fit trying it. Rather than working with a professional to take over a halfway-completed task, it is much better to consider using one before you start. Possibilities are you may require an expert plumber to make tube links.
This post will aid you install a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools as well as material list should consist of the following:
Getting ready for the Installation
First of all, the supporting framework provided with the bath needs to be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of both taps using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be rather troublesome because of the limited gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub until the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable tap connector to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints and also new pipework for leakages and also tighten them if essential. Fill up the tub and additionally examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has been used at the very least when as this will resolve it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers are in place in between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface in between the bathroom and also the tiling, resulting in problems with moisture and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are sold in tubes as well as cartridges, as well as can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill up the tub with water before sealing, to enable the motion experienced when the bathtub remains in usage. The sealer can fracture rather early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that article about Tools You Need to Install a New Bathtub through an acquaintance on a different web address. Do you know about another individual who is occupied with the topic? Do not hesitate to promote it. I appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Course Detail Report this page